Сервис мануал и схема телевизора PIONEER PDP-507XD; PDP-507XA
Файл в формате PDF на английском языкеСодержание:
- 1. NOTES ON SERVICE VISIT
- 1.1 SAFETY INFORMATION
- 1.2 QUICK REFERENCE UPON SERVICE VISIT
- 1.3 JIGS LIST
- 2. EXPLODED VIEWS AND PARTS LIST
- 2.1 PACKING SECTION
- 2.2 REAR SECTION
- 2.3 FRONT SECTION
- 2.4 CHASSIS SECTION (1/2)
- 2.5 CHASSIS SECTION (2/2)
- 2.6 PANEL CHASSIS SECTION
- 2.7 MULTIBASE SECTION
- 2.8 PDP SERVICE ASSY 507 (AWU1212)
- 3. PCB PARTS LIST
- 4. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
- 4.1 OVERALL CONNECTION DIAGRAM (1/2)
- 4.2 OVERALL CONNECTION DIAGRAM (2/2)
- 4.3 OVERALL BLOCK DIAGRAM (1/2)
- 4.4 OVERALL BLOCK DIAGRAM (2/2)
- 4.5 50 ADDRESS S and L ASSYS
- 4.6 50 SCAN A and B ASSYS
- 4.7 50X MAIN DRIVE and 50X SUB DRIVE ASSYS
- 4.8 50Y MAIN DRIVE and 50Y SUB DRIVE ASSYS
- 4.9 50 DIGITAL ASSY
- 4.10 AUDIO ASSY
- 4.11 SIGNAL BLOCK DIAGRAM
- 4.12 R07 DT ASSY (PDP-507XD ONLY)
- 4.13 MAIN ASSY POWER LINE BLOCK DIAGRAM
- 4.14 50 X/Y DRIVE POWER LINE BLOCK DIAGRAM
- 4.15 FUKUGO BLOCK POWER LINE BLOCK DIAGRAM
- 4.16 POWER SUPPLY UNIT
- 4.17 VOLTAGES
- 4.18 WAVEFORMS
- 5. DIAGNOSIS INFORMATION
- 5.1 THE FLOW OF DIAGNOSIS
- 5.1.1 FLOWCHART OF FAILURE ANALYSIS FOR THE WHOLE UNIT
- 5.1.2 FLOWCHART OF FAILURE ANALYSIS FOR THE POWER SUPPLY UNIT
- 5.1.3 FLOWCHART OF FAILURE ANALYSIS FOR THE DIGITAL ASSY
- 5.1.4 FLOWCHART OF FAILURE ANALYSIS FOR THE DRIVE ASSY
- 5.1.5 FLOWCHART OF FAILURE ANALYSIS FOR THE MAIN ASSY
- 5.1.6 FLOWCHART OF FAILURE ANALYSIS FOR THE VIDEO SYSTEM
- 5.1.7 FLOWCHART OF FAILURE ANALYSIS FOR THE AUDIO SYSTEM
- 5.2 POWER DOWN
- 5.2.1 BLOCK DIAGRAM OF THE POWER-DOWN SIGNAL
- 5.2.2 POWER DOWN OF FAILURE ANALYSIS
- 5.3 SHUT DOWN
- 5.3.1 BLOCK DIAGRAM OF THE SHUT-DOWN SIGNAL
- 5.3.2 SHUT DOWN OF FAILURE ANALYSIS
- 5.4 NON-FAILURE SYMPTOMS
- 6. DISASSEMBLY
- 6.1 PCB LOCATION
- 6.2 FLOWCHART OF THE MAIN PARTS AND PC BOARDS EXCHANGE
- 7. ADJUSTMENT
- 7.1 PARTS CHANGE OF NOTES
- 7.2 ADJUSTMENT REQUIRED WHEN THE SET IS REPAIRED OR REPLACED
- 7.3 ADJUSTMENT REQUIRED WHEN PART IS REPLACED
- 7.4 BACKUP WHEN THE PANEL UNIT IS ADJUSTED
- 7.5 ADJUSTMENTS WHEN THE SERVICE PANEL ASSY IS REPLACED
- 7.6 ADJUSTMENTS WHEN THE DRIVE ASSYS ARE REPLACED
- 7.7 HOW TO CLEAR HISTORY DATA
- 8. SERVICE FACTORY MODE
- 8.1 OUTLINE OF THE SERVICE FACTORY
- 8.1.1 SERVICE FACTORY MODE TRANSITION CHART
- 8.1.2 HOW TO ENTER/EXIT SERVICE FACTORY MODE
- 8.1.3 OPERATION OF SERVICE FACTORY MODE
- 8.1.4 REMOTE CONTROL CODE
- 8.1.5 FACTORY HIERARCHICAL TABLE
- 8.1.6 INDICATIONS IN SERVICE FACTORY MODE
- 8.2 FACTORY MENU
- 8.2.1 INFORMATION
- 8.2.2 PANEL FACTORY MODE
- 8.2.3 OPTION
- 8.2.4 INITIALIZE
- 9. LIST OF RS-232C COMMANDS
- 9.1 OUTLINE OF RS-232C COMMANDS
- 9.1.1 PREPARED TOOLS
- 9.1.2 USING RS-232C COMMANDS
- 9.1.3 COMMAND PROTOCOL
- 9.1.4 DEFINITION OF COMMAND
- 9.2 LIST OF RS-232C COMMANDS
- 9.3 OUTLINE OF COMMANDS
- 9.3.1 QS1
- 9.3.2 QS2
- 9.3.3 QIP
- 9.3.4 QAJ
- 9.3.5 QPW
- 9.3.6 QPM
- 9.3.7 QPD
- 9.3.8 QSD
- 9.3.9 QS6
- 9.3.10 QMT
- 9.3.11 QNG
- 9.3.12 DRV
- 9.3.13 OTHER COMMANDS
- 10. GENERAL INFORMATION
- 10.1 POWER ON SEQUENCE
- 10.2 POWER SUPPLY TRANSITION STATUS
- 10.3 POWER ON/OFF FUNCTION FOR THE LARGE-SIGNAL SYSTEM
- 10.4 LED INFORMATION
- 10.5 SPECIFICATION ABOUT THE THERMAL PROTECTION
- 10.6 PROCESSING IN ABNORMALITY
- 11. SPECIFICATIONS
- 11.1 MAIN SPECIFICATIONS
- 11.2 ACCESSORIES
- 11.3 PANEL FACILITIES
- 12. IC INFORMATION
